Make sure you go through and revise the third lesson of D.C circuits, so that you do better in this test. As this test can be taken only once, and your score will be saved.
Make sure you have a scientific calculator with you before you start, for calculations.
This test will show, how well you are prepared for the exam. So don’t forget to revise before you start.
This mega test includes 139 D.C circuits Questions.
Total time for this mega test is 2 hours 19 minutes.
You have 1 minutes for each question.
Good Luck!
0 of 139 questions completed
Questions:
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
0 of 139 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Pos. | Name | Entered on | Points | Result |
---|---|---|---|---|
Table is loading | ||||
No data available | ||||
The diagram shows a battery connected to two identical resistors. Three ammeters M1, M2 and M3 are connected in the circuit.
Meter M1Â reads 1.0A .
What are the readings on M2 Â and on M3 ?
Remember: The current is the same everywhere in a series circuit.
A 30 Ω resistor is connected in series with another resistor and a 6.0 V battery.
The current in the circuit is 0.12 A. A voltmeter is connected across the other resistor.
What is reading on the voltmeter?
First, Calculate the Voltage across the 30? resistor, using the Ohm’s law equation.
Then, As the total potential difference or e.m.f is divided between the two resistors in series, Subtract the V you just calculated from the total Voltage or e.m.f across the battery.
The diagram shows an electric circuit containing three meters, X, Y and Z, all connected correctly.
What are the meters X, Y and Z?
Remember that Ammeter is always connected in series while voltmeter is always connected in parallel.
A student sets up a circuit containing a battery of two cells and three lamps, as shown.
What is the circuit diagram for this arrangement?
If you are not getting this, means you need to revise.
What is the resistance of this combination?
A   0.14Ω     B   0.58Ω    C  1.7Ω     D   7.0Ω
Combined Resistance in parallel = 1 / R1 + 1 / R2
Then the fraction you get, make it upside down (means take denominator up and numerator down) and you will get the answer.
You have to use the calculator to calculate this answer.
A 3.0Ω resistor and a 6.0Ω resistor are connected in parallel.
What is their combined resistance?
A   0.50Ω    B  2.0Ω    C   4.5Ω    D   9.0Ω
Two resistors are connected in parallel.
Which value could be the resistance of the combination?
A    12Ω    B   20Ω    C   25Ω    D   50Ω
If you are not getting it, that means you need to revise.
A student connects various resistors in parallel pairs.
Underneath each diagram is a statement about the total resistance of each pair of resistors.
Which statement is correct?
Two resistors, with resistances R1 and R2 are connected in parallel.
The resistance R1 is greater than the resistance R2.
What is the resistance of the Parallel combination?
Which statement is not correct for lamps connected in parallel?
The diagram shows four arrangements of resistors.
Which arrangement has the smallest total resistance?
A 12 V battery is connected to a combination of 2.0Ω resistors as shown.
What is the current in the battery?
A Â Â 1.5 AÂ Â Â Â Â Â Â Â BÂ Â Â Â 2.0 AÂ Â Â Â Â Â Â Â Â CÂ Â Â 4.0AÂ Â Â Â Â Â Â Â D Â Â Â 6.0A
The circuit diagram shows a 4.0Ω resistor and an 8.0Ω resistor connected to a 6.0V
battery.
What is the potential difference (p.d.) across the 4.0Ω resistor?
A Â Â 0.5V Â Â Â Â Â BÂ Â 2.0VÂ Â Â Â Â CÂ Â 4.0VÂ Â Â Â Â D Â Â 6.0V
The 4.0Ω resistor and an 8.0Ω resistor connected to a 6.0V battery.
What is the current in the 8.0Ω resistor?
AÂ Â Â Â 0A Â Â Â Â Â Â BÂ Â Â 0.50A Â Â Â Â Â Â Â CÂ Â Â 0.75A Â Â Â Â D Â Â 1.0A
The circuit diagram includes two resistors connected in parallel.
Which statement is correct?
The reading on the ammeter in the circuit is 1.0A.
A second ammeter is connected in the circuit. It also reads 1.0A.
At which labelled point is it connected?
A circuit contains four ammeters A, B, C and D, and three resistors with different values.
Which ammeter shows the largest reading?
The diagram shows a circuit containing three ammeters P,Q and R.
Which statement about the readings on the ammeters is correct?
A circuit contains four ammeters and three resistors with different values.
Which ammeter shows the largest reading?
The diagram shows a circuit used to find the resistance of lamp L.
Blocks P, Q and R represent the different components used.
Which is a correct possible choice of components to use for P, Q and R?
A student investigates a circuit that contains two parallel resistors. The circuit includes meter R, S and T which are all connected correctly.
Which type of meters are R, S and T?
In the circuit shown ammeter X reads 0.5A.
What does ammeter Y read?
AÂ Â 0Â Â Â Â Â Â BÂ Â 0.5AÂ Â Â Â Â Â C Â Â 3.5AÂ Â Â Â Â Â Â DÂ Â Â 4.0A
The diagram shows a circuit containing a d.c. power supply, a motor and a variable resistor. Three ammeters X, Y and Z shows the current in different parts of the circuit.
The reading on X is 4.0 A.
Which statement is correct?
AÂ Â The readings on Y and Z are both less than 4.0A.
B  The readings on Y and Z are both equal to 4.0A.
CÂ Â The readings on Y and Z are both greater than 4.0A.
DÂ Â The reading on Z is zero.
A student carries out an experiment to investigate the resistance of a resistor R. She takes a series of readings of potential difference(P.D.) and current, and plots a graph for her results.
Which circuit should she use?
Â
The diagram shows a torch containing two cells, a switch and a lamp.
Which is the circuit diagram for the torch?
A lamp is to be connected in a circuit so that the potential difference (p.d.) across it can be varied from 0 to 6V.
Which circuit would be most suitable?